
If you’re asking, “How much wood should I buy?” the short answer is: buy more than the finished dimensions of your parts add up to usually somewhere between 15% and 40% more, depending on the project. The exact number depends on the finished parts you need, the rough lumber dimensions available, how complex the project is, the quality of the boards you’re choosing from, grain direction, and how much material gets removed during milling.
There’s no single percentage that works for every project. A simple shelf with straight cuts and clean pine needs a lot less cushion than a curved chair built from figured walnut. The goal of this article is to walk through the actual planning process, so you can come up with a number that fits your specific build instead of guessing. Before reading the buying guide, if you already know the thickness, width, length, and quantity of your lumber, use our Board Foot Calculator to quickly calculate the total board feet.
Table of Contents
Start with a Cut List
Before you buy anything, make a cut list. This is just a table of every part in your project, with its finished thickness, width, and length. Skipping this step is the single most common reason people either run short on lumber or come home with a stack of boards that don’t quite work.
Say you’re building a small side table. Your cut list might look like this:
| Part | Quantity | Finished thickness | Finished width | Finished length |
| Tabletop boards | 5 | 3/4 in | 5 in | 48 in |
| Legs | 4 | 1 1/2 in | 1 1/2 in | 28 in |
| Aprons | 2 | 3/4 in | 4 in | 40 in |
| Side aprons | 2 | 3/4 in | 4 in | 18 in |
This is just an illustrative example your table might use different dimensions entirely. The point is that once you have every part listed with its finished size, you have something concrete to build an estimate from. Guessing “I probably need about two sheets of lumber” isn’t a plan; a cut list is.
Finished Wood vs. Lumber You Buy
This is where a lot of estimates go wrong, and it’s worth slowing down on. The dimensions in your cut list are finished dimensions the size the part needs to be after it’s been milled, planed, jointed, and cut clean. The lumber you buy at the yard is rough lumber, and rough lumber is not the same size as finished lumber.
A board that’s rough-sawn to a full 1 inch thick will typically finish out closer to 3/4 inch after it’s been surfaced on both faces. A board that’s rough-sawn 6 inches wide might only yield 5 1/2 inches of usable width once the edges are jointed straight. Length gets trimmed too, since the ends of rough boards are often split, checked, or just not square.
So, if your cut list adds up to 20 board feet of finished material, you do not buy 20 board feet of rough lumber. You buy more, because milling removes material you can’t get back. This is the biggest reason people fall short on a project even after doing the math they calculated the board footage of the finished parts and bought exactly that amount, then discovered there wasn’t enough left over once the boards were surfaced and squared.
Estimate the Usable Lumber
Not every square inch of a board is going to become part of your furniture. Some of it gets planed away on purpose during milling. Some of it has to be avoided because it’s simply not good enough to use.
Common reasons a section of a board ends up in the scrap pile:
- Knots, especially loose ones or ones near the edge of a part
- Cracks and checks, usually at the ends of the board
- Wane, where the bark edge cuts into the width of the board
- Twist, cup, or bow severe enough that flattening it would remove too much thickness
- Sapwood, if your project calls for heartwood color consistency
- Damaged or split ends
- Grain that runs the wrong direction for the part you need
- Short offcuts that are too small to be useful for anything else in the project
None of this means every board is full of problems. A good, clear board from a reputable supplier might only lose a small amount to milling allowance and squaring. A cheaper or lower-grade board might lose a lot more. The point isn’t to expect the worst it’s to build in enough room that an average board, with an average number of small issues, still gets you where you need to go.
How Much Extra Wood Should You Buy?
This is the question most people actually want answered, so here’s a practical way to think about it rather than a single number to memorize.
Simple projects with straight parts and good lumber think shelving, a plain bench, or anything built from clear, straight-grained stock need a relatively small cushion. You’re mostly accounting for saw kerf, squaring the ends, and the normal loss from planning.
Normal furniture projects with ordinary cutting and milling a typical table, a dresser, a bookcase need a moderate allowance. You’re now also accounting for a wider variety of part sizes, a few defects here and there, and the reality that not every board in a batch is equally clean.
Complex projects curved parts, figured or expensive wood, many small components, or lower-grade lumber need a larger allowance. Curved cuts throw away a lot of material as offcuts that can’t be reused. Figured wood is graded more for looks than yield, so it often has more unusable sections. And projects with lots of small parts are harder to nest efficiently on a board, which leaves more scrap.
As a general reference point, The Wood Whisperer suggests starting around 15% extra for straightforward projects and increasing that depending on the shape of the parts, the species, and the grade of lumber being used, while some woodworkers plan closer to 25% and go higher still when working with knotty material. Some woodworkers suggest buying five to ten percent more than the calculated board footage for simple, straight-line projects.
A Simple Furniture Lumber Estimate Example
Let’s walk through the small table from the cut list above and turn it into a purchasing decision.
Step 1: Calculate the finished board footage.
Board feet = (thickness in inches × width in inches × length in inches) ÷ 144, multiplied by quantity.
- Tabletop boards: 0.75 × 5 × 48 ÷ 144 = 1.25 BF each × 5 = 6.25 BF
- Legs: 1.5 × 1.5 × 28 ÷ 144 = 0.4375 BF each × 4 = 1.75 BF
- Aprons: 0.75 × 4 × 40 ÷ 144 = 0.833 BF each × 2 = 1.67 BF
- Side aprons: 0.75 × 4 × 18 ÷ 144 = 0.375 BF each × 2 = 0.75 BF
Total finished material: roughly 10.4 board feet.
Step 2: Account for milling loss.
Since rough lumber loses thickness and width during surfacing, add a milling allowance. A common approach is to buy lumber roughly one nominal size thicker than the finished target buying 4/4 (nominal 1 inch) rough stock to get a 3/4-inch finished part, for example which already builds some of this loss into your board footage once you calculate it off the rough dimensions rather than the finished ones.
Step 3: Account for defects and cutting loss.
This project is straightforward straight parts, no curves so a moderate allowance is reasonable. Adding 20% to the finished total: 10.4 BF × 1.20 ≈ 12.5 BF.
Step 4: Round to practical purchasing quantities.
Lumber is sold in specific board sizes, not arbitrary board-foot totals. If the boards available are roughly 6 inches wide and 8 feet long, that’s about 4 board feet per board, so you’d plan on purchasing around 3 to 4 boards to comfortably cover 12.5 board feet, accounting for the fact that not every inch of every board will be usable.
That’s the method: finished total, adjust for milling, add a project-appropriate allowance, then round up to real boards you can actually buy.
Don’t Buy Only by Total Board Feet
Here’s a trap worth avoiding: two lumber orders can have the exact same board-foot total and still be completely different in usefulness. Twenty board feet spread across several boards that are wide enough and long enough for your parts will work fine. Twenty board feet made up of narrow, short boards might not work at all, even though the math says you have “enough wood.” Board feet is a volume measurement it doesn’t know or care whether the wood is in the right shape for your project.
Before you buy, check that the boards available can actually produce your longest parts and your widest parts. A board-foot total that looks sufficient on paper can still leave you short if none of the individual boards are long enough for your table legs, or wide enough for a single-board tabletop panel.
Match Boards to Parts
Once you know roughly how much lumber you need, think about which boards should go toward which parts.
- Save your widest boards for wide components, like a tabletop or a wide drawer front.
- Save your longest boards for long components, like legs or rails, where you can’t join two shorter pieces together.
- Reserve the clearest, best-looking sections for visible parts of the furniture.
- Use less attractive sections knottier, less consistent grain for hidden parts like drawer sides or web frames, where appearance doesn’t matter as much.
Thinking this through before you cut anything reduces waste, because you’re not discovering halfway through the project that your best board got used on a part nobody will ever see.
How Lumber Species and Grade Affect the Amount to Buy
Species and grade both affect how much usable material you actually get out of a given amount of lumber. Higher grades of lumber are graded specifically on how much clear, usable material a board yields, so a higher-grade board generally gives you more finished material per board foot purchased. Lower grades cost less per board foot, but often have more knots, more wane, and more defects to cut around so the effective cost per usable board foot can end up higher than it looks on the price tag.
Species also matters. Some species are more prone to certain defects, tend to have more color variation, or are simply harder to source in wide or long boards, which affects how efficiently you can lay out your cut list. None of this means you need to become an expert in every species before buying lumber it just means the “cheapest price per board foot” option isn’t automatically the cheapest option once your account for what you can actually use.
Rough-Sawn Hardwood and Board-Foot Buying
Hardwood is commonly sold by the board foot rather than by a fixed board size, which is part of why board-foot estimates are so useful for furniture projects they let you compare lumber of different thicknesses, widths, and lengths on equal footing.
If you already know the dimensions and quantities of the boards you’re considering, the Board Foot Calculator is a quick way to total up the board footage and get an estimated material cost before you commit to an order.
Common Mistakes When Buying Furniture Lumber
- Buying exactly the calculated finished volume, with no allowance at all
- Ignoring the loss between rough and finished thickness
- Choosing boards based only on total board feet, without checking individual board dimensions
- Forgetting to check that the longest and widest parts are actually covered
- Underestimating how much material defects will remove
- Buying lumber before making a cut list
- Assuming every board of a given species is equally usable
- Not buying enough matching material for a tabletop or panel that needs consistent color and grain
- Shopping only by price per board foot instead of usable material per board foot
- Not inspecting boards in person before purchasing, when that option is available
How to Use the Board Foot Calculator For Furniture Project
Once your cut list and allowance are worked out, the calculator becomes a quick way to check your numbers:
- Build your parts list with finished dimensions.
- Estimate the rough lumber you’ll need, including your milling and waste allowance.
- Identify the actual boards you’re considering buying.
- Enter the thickness, width, length, and quantity of those boards into the Board Foot Calculator.
- Compare the calculator’s total against your project estimate.
- Adjust the order up or down based on your project’s complexity.
Frequently Asked Questions
How do I estimate lumber for a furniture project?
Start with a cut list of finished part dimensions, convert that to board feet, add an allowance for milling and defects, and round up to the actual board sizes available.
How much extra wood should I buy for woodworking?
It depends on the project. Simple, straight-part projects with good lumber need a smaller allowance; complex projects with curves, many parts, or lower-grade wood need more.
Should I calculate board feet from rough or finished dimensions?
Both have a purpose finished dimensions tell you what the project needs, while rough dimensions of the boards you’re buying tell you what you’re actually purchasing. They shouldn’t be treated as the same number.
Is buying 10% extra lumber enough?
For a very simple project with clean, straight lumber it might be. For most furniture projects with any complexity, it’s often on the low side.
How do I account for knots and defects?
Inspect boards before buying when possible and build extra material into your estimate rather than assuming every board is defect-free.
Should I buy wider boards for furniture?
Where the design calls for its wide tabletop components especially yes, since narrower boards can force extra joints, you may not want.
How do I estimate lumber cost for a furniture project?
Total your estimated board footage, including your allowance, and multiply by the price per board foot for the lumber you’re considering the Board Foot Calculator handles this automatically.
Related Tools: Once you’ve settled on how much lumber to buy, a couple of other calculators can help with the next steps. The Lumber Calculator is useful if you’re buying dimensional lumber packs and want to work out exact piece counts and a buffer for trimming. If you’re trying to figure out how many stock boards you’ll need to produce a set number of finished parts at a given length, the Wood Cut List Calculator will map that out for you, including offcut waste and kerf loss per board.